the following ink may have run out calour canon MP250, IP 2270, MP160, iP2700

When the printer is turned on seems OK, but after the print command, it will display Blink 13x Orange on the Canon MP250, MP160, iP2770, iP2700

 the following ink may have run out Color

Blink 13x Orange lights with the picture above, means catrid color reset press the Resume button requires a bit longer until the GREEN light flashes, then release. black catridge also need to be reset and the picture is as follows:

 the following ink may have run out Black

Same way: rather long press the Resume button until the GREEN light flashes, then release.after doing these steps then the printer will return to normal. This often occurs when the cartridge runs out complete refill then installed again.

ERROR CODE AND RESET CANON MP150 MP160

E9 The connected digital camera / video camera does not support Camera
Direct Printing
E14 The Ink cartridges whose destination are wrong
E15 Ink cartridge is not installed E16 - Ink remaining is unknown
E16 -E19 Failed to scan head alignment sheet
E22 Carriage error
E23 Paper feed error
E24 Purge unit error
E25 ASF(cam) sensor error
E26 Internal temperature rise error
E27 Waste ink absorber full or platen waste ink absorber full
E28 Ink cartridge temperature rise error -
E29 EEPROM error
E33 Paper feed position error
E35 15 USB Host VBUD overcurrent error - USB
E37 17 Abnormal motor driver error
E40 20 Other hardware error
E42 22 Scanner error

Canon Error Code E101,E102, E110, E120, E121, E140, E141, E142, E143, E144, E145, E146 Eror code Canon

E101 The AF motor of the laser unit is faulty.
E102 The light intensity of the laser does not reach a specific level.
E110 The polygonal scanner motor does not reach a specific speed
within a specific time.
E111 The polygonal cooling fan does not rotate properly.
E120 The temperature of the laser does not reach a specific value.
E121 The stoppage of the laser cooling fan is detected.
E140 The movable guide motor is turned ON, and a specific position
cannot be detected within a specific time.

E141 1. The capping motor is turned ON, and a specific position cannot
be detected within a specific time.
2. A specific position of the cam sensor for the recovery system cannot be
detected within a specific time.
E142 The pressure position switching motor is turned ON, and a specific
position cannot be detected within a specific time.
E143 The intake switching motor is turned ON, and a specific position
cannot be detected within a specific time.
E144 A detection signal is not returned to the ink pump monitor after the
ink pump is activated: DCC -> BHD -> pump drive signal
E145 No signal is generated from the position sensor within a specific
time after a drive signal of the cutter motor is generated.
E146 1. The waste ink full sensor is turned ON.
2. The intake counter for waste ink exceeds a specific value.

Error Code E064 Canon iR3300 Series

Symptom

E064 is indicated on the control panel. The error description is: The presence of a high voltage error is communicated by the composite power supply. The output for primary charging, developing, or transfer has deviated from a specific level of voltage.

Cause
* Adjustments in Service Mode are Incorrect
* Transport Assembly is Not Engaging Properly
* Dirty HVT Contacts for Developing Assembly and Charging Rollers
* A Paper Clip on HVT Contacts or Developing Assembly
* Faulty Transfer Roller
* Faulty Static Charge Eliminator
* Defective Composite Power Supply
* Defective DC Controller PCB Assembly

Action

1. Check the values in Service Mode and make sure they correspond to the Service
Label. If the copier receives a spike or surge through the 240V line these values
can change (can also give you blank copies). Take particular note of the Dev Bias
setting. [COPIER > ADJUST > DEVELOP > DE-DC]
2. Make sure the Transport Assembly is engaging properly. The Transfer Roller should
make good contact with the drum. Check condition of screw (XB6-7501-007) and
Pressure Plates (FB5-4816-000 & FB5-4817-000) for the Transport Assembly.
3. Clean HVT contacts for Primary/ Transfer Charging Rollers and Developing
Assembly. Inspect for any paper clips.
4. Replace the Transfer Roller (FF6-0104-000).
5. Replace the Static Charge Eliminator (FF5-7246-000).
6. Replace Composite Power Supply followed by DC Controller PCB Assembly.