E101 The AF motor of the laser unit is faulty.
E102 The light intensity of the laser does not reach a specific level.
E110 The polygonal scanner motor does not reach a specific speed
within a specific time.
E111 The polygonal cooling fan does not rotate properly.
E120 The temperature of the laser does not reach a specific value.
E121 The stoppage of the laser cooling fan is detected.
E140 The movable guide motor is turned ON, and a specific position
cannot be detected within a specific time.
E141 1. The capping motor is turned ON, and a specific position cannot
be detected within a specific time.
2. A specific position of the cam sensor for the recovery system cannot be
detected within a specific time.
E142 The pressure position switching motor is turned ON, and a specific
position cannot be detected within a specific time.
E143 The intake switching motor is turned ON, and a specific position
cannot be detected within a specific time.
E144 A detection signal is not returned to the ink pump monitor after the
ink pump is activated: DCC -> BHD -> pump drive signal
E145 No signal is generated from the position sensor within a specific
time after a drive signal of the cutter motor is generated.
E146 1. The waste ink full sensor is turned ON.
2. The intake counter for waste ink exceeds a specific value.
Tampilkan postingan dengan label canon eror code E006. Tampilkan semua postingan
Tampilkan postingan dengan label canon eror code E006. Tampilkan semua postingan
Canon Error Code, E000, E001,E002,E003,E004,E005
E000
The fixing temperature does not go up after turning ON the power
due to a fault in the thermistor or the heater, etc., (e.g. It does not
reach 70°C degrees within 2 min.)
E001
The fixing temperature abnormally goes up due to a fault in the
thermistor or SSR, etc.
E002
The fixing temperature does not reach a specific temperature due
to a fault in the thermistor or the heater, etc.
e.g) The fixing temperature does not go up to 190°C degrees
within 5 min after reaching 70°C degrees.
E003
The fixing temperature drops abnormally after wait time is up due
to a fault in the thermistor, the heater, etc. (e.g. After wait time is
up, the fixing temperature drops to 70°C degrees).
E004
A short circuit in the fixing heater drive circuit (SSR, etc) is
detected.
E005 The fixing web is wound up completely.
E006 The fixing drawer connector is not connected as the front door is closed.
E007 The fixing film is off to the side.
E008
A specific number of copies are made after the machine detects
that fixing oil is out.
E009 The rated voltages of the power supply and the fixing unit do not
E010 Clock pulses fail to be generated or the PLL lock fails to be
released due to a fault in the main motor unit
E011 Excess current flows to the motor control circuit because the main
E012
Clock pulses fail to be generated or the PLL lock is released due to
a fault in the drum motor, etc.
The fixing temperature does not go up after turning ON the power
due to a fault in the thermistor or the heater, etc., (e.g. It does not
reach 70°C degrees within 2 min.)
E001
The fixing temperature abnormally goes up due to a fault in the
thermistor or SSR, etc.
E002
The fixing temperature does not reach a specific temperature due
to a fault in the thermistor or the heater, etc.
e.g) The fixing temperature does not go up to 190°C degrees
within 5 min after reaching 70°C degrees.
E003
The fixing temperature drops abnormally after wait time is up due
to a fault in the thermistor, the heater, etc. (e.g. After wait time is
up, the fixing temperature drops to 70°C degrees).
E004
A short circuit in the fixing heater drive circuit (SSR, etc) is
detected.
E005 The fixing web is wound up completely.
E006 The fixing drawer connector is not connected as the front door is closed.
E007 The fixing film is off to the side.
E008
A specific number of copies are made after the machine detects
that fixing oil is out.
E009 The rated voltages of the power supply and the fixing unit do not
E010 Clock pulses fail to be generated or the PLL lock fails to be
released due to a fault in the main motor unit
E011 Excess current flows to the motor control circuit because the main
E012
Clock pulses fail to be generated or the PLL lock is released due to
a fault in the drum motor, etc.
Langganan:
Postingan (Atom)