E751 can be displayed when a connection error of the drum unit or toner cartridge occurs. The following are the detail of each sub code. You may find it helpful to refer to them when servicing. The suffix "x" of each sub code shows color of the affected drum unit or toner cartridge. (1=Y, 2=M, 3=C, and 4=k)
- 000x: Drum unit connection error (on printer side)
- 100x: Toner cartridge connection error (on printer side)
- 010x: Drum unit memory writing error
- 110x: Toner cartridge memory writing error
- 020x: Drum unit memory data error
- 120x: Toner cartridge memory data error
- 030x: Drum unit memory writing error (The number of reties exceeds the specified value.)
- 130x: Toner cartridge memory writing error (The number of reties exceeds the specified value.)
Though it can be memory related, it looks like a E751-1003 is Toner cartridge connection error (on printer side) Check the cyan drum or the cyan toner cartridge for now. Keep us posted when you try some of the details above.
Tampilkan postingan dengan label Canon IR error code 602-0003 E602. Tampilkan semua postingan
Tampilkan postingan dengan label Canon IR error code 602-0003 E602. Tampilkan semua postingan
Cannon 2200/3300 Imagerunner HDD failure e602 error
The machine has a error code 602-0003
E602
1) Are the connection and the cable of the connector (J1017) on the main controller PCB and the connector (J1551) on the hard disk drive normal? NO: Correct the cable connection.Hard disk drive (HDD), Main controller PCB
2) Try replacing the hard disk drive and downloading the system software.Is the problem corrected?
YES: End. NO: Replace the main controller PCB.
3) HDD unit.
Remove the rear upper cover and the reader rear cover. Remove the three screws, and detach the cover, Remove the two screws and disconnect the two connectors then, remove the HDD unit. Remove the six screws and detach the HDD When mounting the HDD unit,be sure that the flat cable is under the plastic sheet of the HDD upper case.
E602
1) Are the connection and the cable of the connector (J1017) on the main controller PCB and the connector (J1551) on the hard disk drive normal? NO: Correct the cable connection.Hard disk drive (HDD), Main controller PCB
2) Try replacing the hard disk drive and downloading the system software.Is the problem corrected?
YES: End. NO: Replace the main controller PCB.
3) HDD unit.
Remove the rear upper cover and the reader rear cover. Remove the three screws, and detach the cover, Remove the two screws and disconnect the two connectors then, remove the HDD unit. Remove the six screws and detach the HDD When mounting the HDD unit,be sure that the flat cable is under the plastic sheet of the HDD upper case.
Canon Error Code, E021, E022, E023, E024,E025,E026, E027, E028, E029, E029, E030
E021 The rotor fails to rotate and move properly due to a fault in the developing rotor/motor ass'y.
E022 Pressure fails to be applied to the developer after a specific time
passes after the developer is selected.
E023 The developer sleeve motor fails to rotate properly.
E024 The developer cannot be detected. ( not mounted properly.)
E025 Excess current of the toner delivery motor or the cartridge motor is
E030 The total counters are not functioning.
E031 The optional counters are not functioning.
E032 The counters for ASSIST are not functioning. (Disconnection of
counter pulse for ASSIST.)
E040 The lifter position signal fails to be generated due to a lifter clutch
failure.
E041 The paper deck lifter fails to be detected within a specific time.
E042 The roll paper cutting operation is not functioning properly because
the cut motor does not work, etc.
E043 An abnormal signal is detected due to a fault in the pick-up motor
for the 3-cassette deck/3.5K paper deck.
E050
A malfunction of the holding tray. A fault in the side registration is
included.
E022 Pressure fails to be applied to the developer after a specific time
passes after the developer is selected.
E023 The developer sleeve motor fails to rotate properly.
E024 The developer cannot be detected. ( not mounted properly.)
E025 Excess current of the toner delivery motor or the cartridge motor is
E030 The total counters are not functioning.
E031 The optional counters are not functioning.
E032 The counters for ASSIST are not functioning. (Disconnection of
counter pulse for ASSIST.)
E040 The lifter position signal fails to be generated due to a lifter clutch
failure.
E041 The paper deck lifter fails to be detected within a specific time.
E042 The roll paper cutting operation is not functioning properly because
the cut motor does not work, etc.
E043 An abnormal signal is detected due to a fault in the pick-up motor
for the 3-cassette deck/3.5K paper deck.
E050
A malfunction of the holding tray. A fault in the side registration is
included.
Error Code E064 Canon iR3300 Series
Symptom
E064 is indicated on the control panel. The error description is: The presence of a high voltage error is communicated by the composite power supply. The output for primary charging, developing, or transfer has deviated from a specific level of voltage.
Cause
* Adjustments in Service Mode are Incorrect
* Transport Assembly is Not Engaging Properly
* Dirty HVT Contacts for Developing Assembly and Charging Rollers
* A Paper Clip on HVT Contacts or Developing Assembly
* Faulty Transfer Roller
* Faulty Static Charge Eliminator
* Defective Composite Power Supply
* Defective DC Controller PCB Assembly
Action
1. Check the values in Service Mode and make sure they correspond to the Service
Label. If the copier receives a spike or surge through the 240V line these values
can change (can also give you blank copies). Take particular note of the Dev Bias
setting. [COPIER > ADJUST > DEVELOP > DE-DC]
2. Make sure the Transport Assembly is engaging properly. The Transfer Roller should
make good contact with the drum. Check condition of screw (XB6-7501-007) and
Pressure Plates (FB5-4816-000 & FB5-4817-000) for the Transport Assembly.
3. Clean HVT contacts for Primary/ Transfer Charging Rollers and Developing
Assembly. Inspect for any paper clips.
4. Replace the Transfer Roller (FF6-0104-000).
5. Replace the Static Charge Eliminator (FF5-7246-000).
6. Replace Composite Power Supply followed by DC Controller PCB Assembly.
E064 is indicated on the control panel. The error description is: The presence of a high voltage error is communicated by the composite power supply. The output for primary charging, developing, or transfer has deviated from a specific level of voltage.
Cause
* Adjustments in Service Mode are Incorrect
* Transport Assembly is Not Engaging Properly
* Dirty HVT Contacts for Developing Assembly and Charging Rollers
* A Paper Clip on HVT Contacts or Developing Assembly
* Faulty Transfer Roller
* Faulty Static Charge Eliminator
* Defective Composite Power Supply
* Defective DC Controller PCB Assembly
Action
1. Check the values in Service Mode and make sure they correspond to the Service
Label. If the copier receives a spike or surge through the 240V line these values
can change (can also give you blank copies). Take particular note of the Dev Bias
setting. [COPIER > ADJUST > DEVELOP > DE-DC]
2. Make sure the Transport Assembly is engaging properly. The Transfer Roller should
make good contact with the drum. Check condition of screw (XB6-7501-007) and
Pressure Plates (FB5-4816-000 & FB5-4817-000) for the Transport Assembly.
3. Clean HVT contacts for Primary/ Transfer Charging Rollers and Developing
Assembly. Inspect for any paper clips.
4. Replace the Transfer Roller (FF6-0104-000).
5. Replace the Static Charge Eliminator (FF5-7246-000).
6. Replace Composite Power Supply followed by DC Controller PCB Assembly.
Langganan:
Postingan (Atom)