5700 is a ASF cam error most likely. Here the Canon proceedure for fixing it!
DESCRIPTION: 5 Alternating Blinks (SFP) / ##356 (MFP) - ASF Cam Sensor Error
SOLUTION(S): Adjust the Screws & Main Case Unit
Movement (i.e. from shipping) may cause the plastic guide to move away from the chassis. When this
occurs, the gears cannot rotate properly causing a grinding noise and 5 alternating blinks (SFP) or ##356(MFP) - ASF Cam Sensor Error.
Procedures
Step 1: Remove the Left and Right Covers and the Main Case Unit (main cover).
Step 2: Remove the 4 mounting screws from the Chassis.
Step 3: Remove the Main Unit from the Bottom Case.
Step 4: Turn the Main Unit over (upside down) and place on work surface.
Step 5: Inspect the ASF section of the Main Unit for a gap between the white plastic
guide and the Chassis.
Note: The size of the gap varies. Even if the gap is not visible,
complete the steps below.
Step 6: Disconnect the appropriate cables and remove the Logic Board from the
Chassis.
Step 7: Loosen (do not remove) the 4 mounting screws (the mounting screws can be
found behind the logic board) on the Chassis.
Step 8: Re-seat the white plastic guide so it sits flush against the Chassis. The
tip of the white plastic guide should sit slightly inside the
Mounting screw hole. When seated correctly, the gap will no longer be
resent.
Step 9: Tighten the 4 mounting screws without causing the plastic guide to shift.
Step 10: Reassemble the printer and retest.
Tampilkan postingan dengan label Ink and Toner Cartridges. Tampilkan semua postingan
Tampilkan postingan dengan label Ink and Toner Cartridges. Tampilkan semua postingan
Canon PGI-5 CLI-8 BCI-7e BCI-9 chip Resetter Guide
Canon PGI-5BK, CLI-8, BCI-7E and BCI-9PGBK chip resetter Learn more about the Canon chip resetter
Label:
Ink and Toner Cartridges
Canon i80 Waste Ink Tank Full
Try this to reset the error.
1) Close the print head cover, and turn off the printer. While pressing the Resume/Cancel button, press the Power button. (Do not release the buttons. The LED lights in green to indicate that a function is selectable.)
2) While holding the Power button, release the Resume/Cancel button. (Do not release the Power button.)
3) While holding the Power button, press the Resume/Cancel button three times, and then release the Power and Resume/Cancel buttons. (Each time the Resume/Cancel button is pressed, the LED lights alternately in either orange or green, starting with orange.) During initialization, the LED blinks in green.
4) When the LED stops blinking and lights in green, press the Resume/Cancel button the 4 times. (Each time the Resume/Cancel button is pressed, the LED lights alternately in either orange or green, starting with orange.)
5) Press the Power button. The LED lights in green, and the
selected function is performed. (When the operation completes, the printer returns to the menu selection mode automatically.)
6) Power off then back on and test.
Cheers
1) Close the print head cover, and turn off the printer. While pressing the Resume/Cancel button, press the Power button. (Do not release the buttons. The LED lights in green to indicate that a function is selectable.)
2) While holding the Power button, release the Resume/Cancel button. (Do not release the Power button.)
3) While holding the Power button, press the Resume/Cancel button three times, and then release the Power and Resume/Cancel buttons. (Each time the Resume/Cancel button is pressed, the LED lights alternately in either orange or green, starting with orange.) During initialization, the LED blinks in green.
4) When the LED stops blinking and lights in green, press the Resume/Cancel button the 4 times. (Each time the Resume/Cancel button is pressed, the LED lights alternately in either orange or green, starting with orange.)
5) Press the Power button. The LED lights in green, and the
selected function is performed. (When the operation completes, the printer returns to the menu selection mode automatically.)
6) Power off then back on and test.
Cheers
Langganan:
Postingan (Atom)